SAE AMS5834 Cobalt Alloy, Corrosion and Heat-Resistant, Round Wire 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Vacuum Induction Pl

作者:标准资料网时间:2024-05-18 23:21:14 浏览:9971 来源:标准资料网

Product Code:SAE AMS5834
Title:Cobalt Alloy, Corrosion and Heat-Resistant, Round Wire 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Cold Drawn, and Aged
Issuing Committee:Ams F Corrosion Heat Resistant Alloys Committee
Scope:This specification covers a corrosion and heat resistant cobalt alloy in the form of round wire 0.140 inch (3.56 mm) and under in nominal diameter supplied in straight lengths.

下载地址: 点击此处下载

返回跳至顶部

上一篇: SAE AMS5833 Cobalt Alloy, Corrosion and Heat-Resistant, Round Wire 20Cr - 15Ni - 40Co - 7.0Mo - 16Fe Solution Heat Treat
下一篇: SAE AMS5827 Steel, Corrosion Resistant, Covered Welding Electrodes 16.4cr 4.8ni 0.22cb 3.6cu (Cancelled Sep 2000, Supers

基本信息

标准名称：	钛铁矿精矿化学分析方法第6部分：氧化钙、氧化镁、磷量的测定等离子体发射光谱法
英文名称：	Methods for chemical analysis of ilmenite concentrate— Part 6: Determination of calcium oxide、magnesium oxide、phosphorus content—Inductively coupled plasma atomic emission spectrometry
中标分类：	冶金 >> 金属化学分析方法 >> 稀有金属及其合金分析方法
ICS分类：
替代情况：	替代YS/T 360-1994
发布部门：	中华人民共和国工业和信息化部
发布日期：	2011-12-20
实施日期：	2012-07-01
首发日期：
作废日期：
归口单位：	全国有色金属标准化技术委员会
起草单位：	遵义钛业股份有限公司、金川集团有限公司、云南新立有色金属有限公司、抚顺钛业有限公司
出版社：	中国标准出版社
出版日期：	2012-07-01
页数：	8页

适用范围

本标准规定了钛铁矿精矿中氧化钙、氧化镁、磷量的测定方法。
本标准适用于钛铁矿精矿中氧化钙、氧化镁、磷量的测定。测定范围：氧化钙：0.02%～2.00%；氧化镁0.02%～3.00%；磷：0.001%～0.10%。

前言

没有内容

引用标准

没有内容

所属分类：冶金金属化学分析方法稀有金属及其合金分析方法

Product Code:SAE CPGM2
Title:J1349 Certified Power Engine Data for GM LLT as used in 2010 Cadillac CTS Wagon - Level 2
Issuing Committee:
Scope:This product includes information on the manufacturer, engine, applications, testing location, certified maximum horsepower, certified maximum torque along with the certified curves of horsepower and torque over a wide range of engine RPM speeds.In addition, this product contains complete engine information such as displacement, cylinder configuration, valve train, combustion cycle, pressure charging, charge air cooling, bore, stroke, cylinder numbering convention, firing order, compression ratio, fuel system, fuel system pressure, ignition system, knock control, intake manifold, exhaust manifold, cooling system, coolant liquid, thermostat, cooling fan, lubricating oil, fuel, fuel shut off speed, etc. Also included are all measured test parameters outlined in J2723.